DIY: Scrap Paper Strip Ornaments

IMG_3203_paperstripornament
Up until the last couple of years, Safety Husband and I would go home to Texas for the holidays, and we never felt the need to decorate for the season. For the last couple of years we’ve talked about decorating the “Christmas Tree” that just happens to be growing in our upper yard, and this year we’re making it happen. I’ve been putting my brain power into making ornaments that are either weatherproof, or are meant to be thrown away in January. It’s been a great chance to work through some of the materials I’ve been… ahem… collecting.

I love vintage ornaments and paper, and after a couple of years of experimentation I was ready to combine those two loves in this one ornament design. Super quick, because they are held together by staples, a couple of basic techniques can build a whole tree’s worth of decoration.

IMG_2828_paperstripornament

Supplies

  • Stapler
  • Ribbon (3/8″ to 1/2″ wide is great)
  • Scrap Paper: I used leftover 12×12 scrapbooking paper, but catalog or magazine pages would work well too! If you’re using thin paper, you might want to double up on the number of strips per ornament.
  • Clips: binder clips work great for this, but a clothespin will work in a pinch. (Pun intended.)
  • Scissors

IMG_2867_paperstripornament
To begin, cut about eight 1/2″ strips off your paper. (You can vary the number, just make sure you have an even number of strips.)

IMG_2871_paperstripornament
Cut a length of ribbon about twice the length of your paper strips.

IMG_2900_paperstripornament
Fold the ribbon in half, and stack half the strips on each side. Staple near the bottom of the stack, away from the loop of ribbon.

IMG_2904_paperstripornament
The staple will go through all the paper and the ribbon, securing that point. (Staples must be cheating, because they make this too easy.)

IMG_2921_paperstripornament
Put a clip about halfway down the paper, clamping the whole stack of paper and ribbon. With one hand, hold the clip, and with the other gently pull on the loop of the ribbon.

IMG_2923_paperstripornament
This should cause the paper to pooch out a little on the other side of the clip. Repeat the holding and pulling step, but this time grab the ribbon loop and the two strips of paper closest to it on either side.

IMG_2926_paperstripornament
Repeat again and again, adding another strip on either side, until you reach the outer strip.

IMG_2927_paperstripornament

IMG_2931_paperstripornament
Then carefully put a staple through the area the clip was holding.

IMG_2934_paperstripornament

IMG_2936_paperstripornament
Trim any excess paper with a pair of scissors.

IMG_2950_paperstripornament
If you want, you can curl some of the extra paper to add a little decorative detail. Simply roll the paper around a small pencil or paintbrush to curl it.

IMG_2959_paperstripornament
Once you get the hang of the whole pull method, you can shake things up by doing a similar technique, upside-down.

IMG_2977_paperstripornament
Staple in the middle of your ornament, and turn each strip back down. Once you’ve turned each strip, staple them at the bottom to form a heart shape.

IMG_3014_paperstripornament
Using these two techniques you can make a whole range of funky vintage ornaments.

IMG_3448_paperstripornament
If you get sick of looking at the staples, you can replace them with a couple of stitches. Simply poke a hole in the middle of the stack, and make stitches back and forth to secure the ornament.

IMG_3457_paperstripornament
Remove the staple, and you’ll never know it was there.

IMG_3130_paperstripornament
Or spend that time making a whole army or ornaments. It’s up to you!

IMG_3271_paperstripornament
One set down, more to go.

Comments